High-quality OEM (Original Equipment Manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold Indi...
High-quality OEM (Original Equipment Manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold Indi...
High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually.
If your CV Joint Boot is cracked or torn, dirt and debris will adhere to the grease causing premature wear and eventual failure. We recommend installing new clamps with the boot, large clamp # i...
Genuine part sourced from Porsche AG in Germany to ensure quality, reliability, and precise fitment. Sold individually. 6 Necessary per car. Have a fitment question? We are here to help. Simply...
Overall height 17 mm, bearing has groove in outer ring - thereforeect installation perf Cylindrical Roller Bearing located on the bottom of the gear housing nearest the gear housing. Sold Indivi...
We have these manufactured in Germany by an OEM supplier. It is 20% stronger than the original so it will last longer. When installing we recommend purchasing 4 clips, part # N 012 645 2, a spare ...
This is the differential output shaft bearing that attaches to the differential housing. We recommend replacing this bearing with any differential rebuild. Sold Individually.
This is the rear differential tapered roller bearing that sits between the differential and the flange (closest to the flange). We recommend replacing this bearing with any differential rebuild. ...
This seal prevents the differential from running dry which leads to drivetrain damage. Be sure to inspect it often and replace when necessary. Sold Individually. 2 Necessary Per Car. Left or Ri...
A Diverter valve uses vacuum actuation to re-circulate excess boost pressure into the turbo inlet pipe, allowing for quicker boost recovery. If the inner diaphragm is cracked or torn, boost pressu...
If a door check has separated or ripped out, this repair kit with stainless steel sheets can prevent further tearing or damage. For assembly, it is sufficient to adhere these plates to the sheet m...
This is the smaller base gasket for the door handle. When replacing this gasket, we recommend replacing the exterior large door handle gasket, part # 91153163200 and the securing nuts, part # 9...
This is the outer seal for the window slot, it is most prone to degradation from the elements and should be replaced to keep moisture out of the door. Also fits the 964 89-94 Targa and Cabrio.
This is the threshold trim strip that secures the interior carpet to the threshold / door sill. It prevents shoes from scuffing the carpet / paint on egress / ingress. Replacing the sill plates a...
Drain tubes can become clogged and will eventually lead to corrosion of the head light bucket. If you are upgrading your headlights or servicing them it is a great idea to change the drain tube. ...
This acts as both an engine mount for 911/ 930 / 959 1965-89 and a transmission mount for 1972-86 models with 915 Transmissions. High-quality replacement, designed to perform like the original. ...
This acts as both an engine mount for 911/ 930 / 959 1965-89 and a transmission mount for 1972-86 models with 915 Transmissions. High-quality replacement, designed to perform like the original. ...
This acts as both an engine mount for 911/ 930 / 959 1965-89 and a transmission mount for 1972-86 models with 915 Transmissions. High-quality replacement, designed to perform like the original. ...
Replace the worn-out, original soft rubber engine mount with our higher density, RS specification rubber bushing. It is manufactured of rubber with an 85-shore hardness value. 85-shore is the sam...
This adaptor ring is specifically designed to mate the engine case straight to any universal engine stand, using four 3/8" bolts, allowing for a full 360 degree motion of the motor. Bolts up to eve...
This sensor is designed to measure fluid temperatures, it functions as an oil temperature sensor on the air-cooled models and a coolant temperature sensor on water-cooled models. The signal is use...
Expansion valves regulate the flow of refrigerant. When they start to fail, they can create frost on the vents or the AC compressor, blow warm air or constantly run the AC compressor. Sold Indi...
High-quality OEM (Original Equipment Manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Qty. 9 Ne...
A cost-effective combination of an OEM sway bar drop link with 65 shore rubber bushings. 65-shore rubber hardness value is used on original models at the factory, which means this drop link deliver...
Allow our experienced and knowledgeable staff to assist you. Simply contact us via e-mail or phone (+49 7665 989 90) to experience the advantage of purchasing parts from FVD Brombacher.
Fast Delivery
We keep an extensive inventory on hand. If your order is in stock and you contact us before 12 noon, we can ship it that day via UPS – DHL – DPD.
Secure Payment Methods
We insist upon the highest encryption standards to ensure that your information is safe. Secure payment modalities include Pay Pal, Concardis Credit Card Transactions (PCI DSS Certification) and Bank / Wire Transfer.